This Old Haus
TGlist рейтинг
0
0
ТипАчык
Текшерүү
ТекшерилбегенИшенимдүүлүк
ИшенимсизОрду
ТилиБашка
Канал түзүлгөн датаSep 23, 2020
TGlistке кошулган дата
May 22, 2024Тиркелген топ
Tool Room
93
"This Old Haus" тобундагы акыркы жазуулар
15.05.202500:18
Our spirit lives. Cant stop the signal durov.
Soon™️
Soon™️
14.05.202523:16
.
14.05.202520:04
The Canadian national anthem
https://youtu.be/92ydUdqWE1g?si=uw99SNHm30vPXQ_R
https://youtu.be/92ydUdqWE1g?si=uw99SNHm30vPXQ_R
14.05.202519:51
aaaand we're back
@AtlasRedux
@AtlasRedux
14.05.202519:34
F
14.05.202519:24
Did /3pn/ get banned?
14.05.202517:32
Кайра бөлүшүлгөн:
/CIC/ Half Life War Boys Edition
13.05.202520:54
This is the breech end. As you can see, there are no markings on the round. The revolvers themselves were marked with the S&W trademark, the lack of markings on the ammunition is suspected to be more a reflection of the toolroom nature of the project than in any attempt to make a deniable or clandestine weapon
The missing detail from most of the reports, the reason the initial report was classified (albeit only at the Confidential level), and the cause of the QSPRs unusually high terminal effect for a handgun was in a material breakthrough. While most open source reports suggest that the projectiles in the shot column were lead, steel or even tungsten, they were actually depleted uranium.
The missing detail from most of the reports, the reason the initial report was classified (albeit only at the Confidential level), and the cause of the QSPRs unusually high terminal effect for a handgun was in a material breakthrough. While most open source reports suggest that the projectiles in the shot column were lead, steel or even tungsten, they were actually depleted uranium.
Кайра бөлүшүлгөн:/CIC/ Half Life War Boys Edition
13.05.202520:54
This is the muzzle end of the round. As you can see, the sabot (or the sealant atop it) comes closer to the muzzle than indicated in the diagram.
The high pressure inside the round breaks the “rim” of the piston free of an annular slot that initially retains the piston in the rearward position and forces it forward, ejecting the sabot-contained shot load, until the pressure snaps the piston rim into a similar annular slot positioned to receive it, and drives the “nose” of the piston into the muzzle-end threads. These two engagements arrest the piston’s forward motion. One purpose of the rearward slot is to retain the pistol and prevent it from sliding and ejecting the payload during normal gun handling.
The high pressure inside the round breaks the “rim” of the piston free of an annular slot that initially retains the piston in the rearward position and forces it forward, ejecting the sabot-contained shot load, until the pressure snaps the piston rim into a similar annular slot positioned to receive it, and drives the “nose” of the piston into the muzzle-end threads. These two engagements arrest the piston’s forward motion. One purpose of the rearward slot is to retain the pistol and prevent it from sliding and ejecting the payload during normal gun handling.
Кайра бөлүшүлгөн:/CIC/ Half Life War Boys Edition
13.05.202520:54
This is a schematic of the round from what appears to have been the final report on the weapon after development and combat testing in Vietnam. The report recommended further improvements and then general issue to Infantry and Ranger units. Those improvements were not pursued, and the firearm was never manufactured.
Кайра бөлүшүлгөн:/CIC/ Half Life War Boys Edition
13.05.202520:54
This is believed to be the last and only live round in existence (the ATF caused the destruction of most of them maintained by AAI and the military museum system by declaring them suppressors). The material is high-carbon steel, because the case contains the entire energy of the round, inside a piston. An end cap is screwed on the base of the round; threads in the muzzle end act as a trap to catch a piston. A plastic sheath called a “sabot” wraps around the projectiles and is discarded, much like the sabots used with subcaliber projectiles, when the projectile column exits the muzzle. The muzzle end of the round has a silicone material applied as a sealant.
The round has a dark finish which appears to be some kind of high-tech proto-melonite coating, although most resources describe the ammo as “blued.”
The round has a dark finish which appears to be some kind of high-tech proto-melonite coating, although most resources describe the ammo as “blued.”
Кайра бөлүшүлгөн:/CIC/ Half Life War Boys Edition
13.05.202520:40
The AAI QSPR The QSPR special-purpose revolver that was developed and produced by the AAI Corporation. The QSPR was made from a Smith & Wesson Model 29. Frames in white were provided to AAI by Smaith, and they were modified with a .40 caliber smoothbore barrel and the cylinders were bored out to 0.528″, leaving a minimal web between chambers. (The lost strength was made up for by the strong cartridges). The weapon lacked any sights — it was meant to be used at contact range, inside tunnels, although accuracy to 25 feet was claimed (and Vietnam users reported it was more accurate than their .38 revolvers). Both standard large-frame Smith and aftermarket or custom grips were tried.
13.05.202516:28
.
13.05.202516:18
.
Рекорддор
18.03.202523:59
1.4KКатталгандар19.05.202423:59
0Цитация индекси27.02.202501:49
2.5K1 посттун көрүүлөрү25.02.202512:45
1.2K1 жарнама посттун көрүүлөрү18.02.202500:09
20.55%ER27.02.202502:31
128.71%ERRӨнүгүү
Катталуучулар
Citation индекси
Бир посттун көрүүсү
Жарнамалык посттун көрүүсү
ER
ERR
25.04.202519:35
I've had the same wallet for 20 years
Кайра бөлүшүлгөн:
BUCK👏BREAKERS👏 PARADISE👏
10.05.202506:14
Stumbled upon quite possibly my favorite nigger video of all time lol
30.04.202518:49
10.05.202517:18
I am not giving up on my fave mug
07.05.202520:34
03.05.202509:45
01.05.202522:21
Көбүрөөк функцияларды ачуу үчүн кириңиз.